Microcom Technologies Commander General Purpose Variable Speed Drive GpLV Manual de usuario Pagina 94
- Pagina / 118
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Commander GP User Guide
Issue code: gpxu2
D-2 Menu 0 Parameters
D.2 Fixed-function parameters
common to all macro
configurations
Configuration
0.00 Macro selection,
Configuration,
Saving
RW Uni R
0 ~ 2010 0
Value Function
1000 Save new parameter-values
1233 Restore parameters to their default values
for 50Hz
AC supply frequency (Europe)
1244 Restore parameters to their default values
for 60Hz
AC supply frequency (USA)
2001 Macro 1
Easy mode
2002 Macro 2
Motorized potentiometer
2003 Macro 3
Preset speeds
2004 Macro 4
Torque control
2005 Macro 5
PID control
2006 Macro 6
Axis-limit control
2007 Macro 7
Brake control
2009 Macro 0
General purpose (USA default configuration)
2010 Macro 0
General purpose (EUR default configuration)
Press after setting parameter 0.00 at the
required value.
Frequency limits
0.01 Minimum frequency
RW Uni
0 ~ [0.02] 0Hz
Set 0.01 at the required minimum output frequency
of the Drive for both directions of rotation. The
Drive runs at the minimum frequency when the
frequency reference is zero.
[0.01] is a nominal value; slip compensation may
cause the actual frequency to be higher.
(When the Drive is jogging, [0.01] has no effect.)
0.02 Maximum frequency
Maximum frequency
RW Uni
0 ~ 1000.0 50 (
EURO)
60 (
USA)
Hz
Set 0.02 at the required maximum output
frequency for both directions of rotation. The
frequency reference cannot cause the Drive to run
at a frequency higher than [0.02].
[0.02] is a nominal value; slip compensation may
cause the actual frequency to be higher.
(The Drive has additional over-speed protection.)
Caution
For operation at motor speeds
greater than twice base speed,
contact the supplier of the
motor.
Ramps,
Frequency reference selection,
Current limit
0.03 Acceleration rate
RW Uni
0 ~ 3200.0 5 s/100Hz
Set 0.03 at the required rate of acceleration. Note
that larger values produce lower acceleration. The
rate applies in both directions of rotation.
0.03 does not apply to jog speed. See Menu 2 in
the Commander Gp Advanced User Guide for jog
acceleration and deceleration rates.
- COMMANDERGGpp 1
- COMMANDERGGpp LVLV 1
- General information 2
- Important 2
- Contents 3
- Commander GP User Guide 4
- Issue code: gpxu2 4
- 1 Introduction 5
- 1.3 Configuration layers 6
- 1.4 Default configurations 6
- 1.5 Operating mode 6
- 1.6 User-interface modes 6
- 1.7 Macro configurations 7
- 1.8 Plug-in option modules 8
- 1.9 Serial communications 8
- Introduction 1-5 9
- 1-6 Introduction 10
- 2 Getting Started 11
- 2-2 Getting Started 12
- Getting Started 2-3 13
- 2-4 Getting Started 14
- Getting Started 2-5 15
- 2.3 Introduction to the 16
- 2.4 Working with 17
- 2.5 How macro configurations 18
- 2.6 Initial setting up 19
- 2-10 Getting Started 20
- Enabling Macro 1 20
- Getting Started 2-11 21
- 2-12 Getting Started 22
- Autotune 22
- 2.7 Operating instructions 23
- 2-14 Getting Started 24
- Keypad mode 24
- Trip and enable 24
- Getting Started 2-15 25
- Acceleration rate 25
- Deceleration rate 25
- Braking resistor 25
- 2-16 Getting Started 26
- Voltage-control modes 26
- Getting Started 2-17 27
- Boost voltage 27
- 2-18 Getting Started 28
- 3 Setting Up the Drive 29
- (Macro Configurations) 29
- General purpose 30
- Setting Up the Drive 3-3 31
- 3-4 Setting Up the Drive 32
- Setting Up the Drive 3-5 33
- 3-6 Setting Up the Drive 34
- Setting Up the Drive 3-7 35
- Setting up and using Macro 0 35
- 3-8 Setting Up the Drive 36
- Easy mode 37
- 3-10 Setting Up the Drive 38
- Setting Up the Drive 3-11 39
- 3-12 Setting Up the Drive 40
- Setting Up the Drive 3-13 41
- Setting up and using Macro 1 41
- 3-14 Setting Up the Drive 42
- Motorized potentiometer 43
- 3-16 Setting Up the Drive 44
- Setting Up the Drive 3-17 45
- 3-18 Setting Up the Drive 46
- Setting Up the Drive 3-19 47
- Setting up and using Macro 2 47
- 3-20 Setting Up the Drive 48
- Preset frequencies 49
- 3-22 Setting Up the Drive 50
- Setting Up the Drive 3-23 51
- 3-24 Setting Up the Drive 52
- Setting Up the Drive 3-25 53
- Setting up and using Macro 3 53
- 3-26 Setting Up the Drive 54
- Torque control 55
- FREQUENCY CONTROL 55
- TORQUE CONTROL 55
- 3-28 Setting Up the Drive 56
- Setting Up the Drive 3-29 57
- 3-30 Setting Up the Drive 58
- Setting Up the Drive 3-31 59
- Setting up and using Macro 4 59
- 3-32 Setting Up the Drive 60
- PID (set-point control) 61
- PID CONTROL 61
- 3-34 Setting Up the Drive 62
- Setting Up the Drive 3-35 63
- 3-36 Setting Up the Drive 64
- Setting Up the Drive 3-37 65
- Setting up and using Macro 5 65
- Axis-limit control 66
- Setting Up the Drive 3-39 67
- 3-40 Setting Up the Drive 68
- Setting Up the Drive 3-41 69
- 3-42 Setting Up the Drive 70
- Setting Up the Drive 3-43 71
- Setting up and using Macro 6 71
- 3-44 Setting Up the Drive 72
- Brake control 73
- 3-46 Setting Up the Drive 74
- Setting Up the Drive 3-47 75
- 3-48 Setting Up the Drive 76
- Setting Up the Drive 3-49 77
- Setting up and using Macro 7 77
- 3-50 Setting Up the Drive 78
- A Programming 79
- Instructions 79
- A-2 Programming Instructions 80
- A.6 Selecting 81
- A.7 Changing the value of a 82
- Programming Instructions A-5 83
- A-6 Programming Instructions 84
- A.13 Restoring the Drive 85
- A-8 Programming Instructions 86
- B Security 87
- B-2 Security 88
- C Signal Connections 89
- C-2 Signal Connections 90
- Signal Connections C-3 91
- C-4 Signal Connections 92
- D Menu 0 Parameters 93
- D.2 Fixed-function parameters 94
- Menu 0 Parameters D-3 95
- D-4 Menu 0 Parameters 96
- Voltage boost 96
- PWM switching frequency 98
- Menu 0 Parameters D-7 99
- Motor parameters 99
- Drive software build number 99
- Status information 99
- D.3 Parameters specific 100
- Menu 0 Parameters D-9 101
- D-10 Menu 0 Parameters 102
- Menu 0 Parameters D-11 103
- D-12 Menu 0 Parameters 104
- Menu 0 Parameters D-13 105
- D-14 Menu 0 Parameters 106
- Menu 0 Parameters D-15 107
- D-16 Menu 0 Parameters 108
- Menu 0 Parameters D-17 109
- D-18 Menu 0 Parameters 110
- Menu 0 Parameters D-19 111
- D-20 Menu 0 Parameters 112
- Menu 0 Parameters D-21 113
- D-22 Menu 0 Parameters 114
- E Diagnostics 115
- E.3 Trip codes 116
- Diagnostics E-3 117
- E-4 Diagnostics 118
Whirlpool LFF 8M132 manuales
Manuales del propietario y guías del usuario para Lavaplatos Whirlpool LFF 8M132.
Ofrecemos 1 manuales en pdf Whirlpool LFF 8M132 para descargar gratis por tipos de documentos: Instrucciones de uso
Comentarios a estos manuales